on-Line Partial Discharge Tester for Cable, Gis, Circuit Breaker Monitoring

• Customization: Available
• After-sales Service: Life Long Support
• Warranty: 1 Year
• Model NO.: HM9001
• Type: Partial Discharge Detector
• Power Source: AC220V
• Product Name: Partial Discharge Detector
• Detection Methods 1`: Ae
• Detection Methods 2`: Tev
• Detection Methods 3`: UHF
• Detection Methods 4`: Hf
• Lithium Battery Pack: 24V/5ah
• Synchronization: External Synchronization AC10~380V, with Virtual S
• Wireless Synchronization: AC10~380V
• System Platform: Wince6.0, 1 Network Port, 1 USB Port, Support Flas
• Transport Package: Wooden Box with Foam Inside
• Trademark: HMDQ
• Origin: Hubei, China(Mainland)
• Production Capacity: 500sets/ Month

Product Description

on-Line Partial Discharge Tester for cable, GIS, circuit breaker monitoring

I. Product overview    
tThis product can be widely used in the partial discharge detection of power systems, including high-voltage switchgear, ring main unit, voltage/current transformer, transformer (including dry-type transformer), GIS, overhead lines, cables and other equipment insulation state detection, through the following indicators to measure the degree of discharge of electrical equipment:
Partial Discharge Intensity Detection: The intensity of partial discharge is characterized according to the maximum value (dB) in the discharge pulse sequence by measuring the discharge signal within 1 power frequency cycle.
Partial discharge frequency detection: By measuring the discharge signal within 1 power frequency cycle, the discharge pulse is extracted and the frequency of partial discharge is characterized according to the number of discharge pulses.




II.Technical parameters  

TEV measurement		AE measurement
Measuring range	0dB~60dB	Measuring range	0dB ~ 60dB
Resolution	1dB	Resolution	1dB
Precision	±1dB	Precision	±1dB
Maximum pulse per cycle	1400	Frequency range	20~200 kHz
Measurement frequency bands	3~100MHz
AA ,AA1,AA 2measurement		UHF measurement
Measuring range	0dB~60dB	Detection bands	300~2000MHz
Resolution	1dB	Measuring range	0dB~60dB
Precision	±1dB	Sensitivity	<1dB
Sensor center  frequency	40 kHz	Sensor bands	300~2000MHz
HFCT measurement
Sensor transmission impedance	5mV/mA
Frequency of detection	1~30MHz
Sensitivity	≤50pC
hardware
Apperance	ABS
Display	4.3 inch RGB LCD screen with resolution 800*480
Sampling accuracy	12bit
Synchronization mode	Synchronization within the country
Connector	USB port (also charger input)
Earphone	8 ohms minimum
SD card	16G~64G as standard
Built-in battery	3.7V/10000mAh lithium battery
Working time	Approximately 12 hours
Charger	DC 5V/3A
Temperature	-20~50ºC
Humidity	20%~85% relative humidity
Volume, weight	210*100*35(mm) 0.4KG(host)

 III.Product Features
1. Configure different sensors to realize the partial discharge detection of almost all high-voltage electrical equipment;
2.Provide a variety of discharge patterns such as time-domain waveform, PRPD, PRPS, etc., to realize the analysis of different discharge types;
3.Humanized man-machine interface facilitates data management of different devices;
4.Built-in ultrasonic sensor and transient ground voltage (hereinafter referred to as TEV) sensor, which can be connected to special sensors such as transformers, GIS, overhead lines, cables, etc.;
5.The non-invasive detection method does not require power failure during the test process, and there is no need to configure an additional high-voltage source, which is more convenient to use than the traditional pulsed partial discharge detector;
6.The test bandwidth range is 30kHz ~ 2.0GHz, which is suitable for the detection principle of various frequency bands;